Pre-test

Before you begin this course, test your skills by taking the following assessment to see where you stand.

Keep track of your incorrect answers to know which skills you should study. You'll have a chance to take this same practice test again at the end of the course to see how you've improved.

All questions must be answered to submit your assessment.

Pre-assessment

49 questions

What alignment is the width of a widening alignment based on?

(Select one)

The parent alignment.
The outermost offset alignment.
The curb return alignment.
The innermost offset alignment.

Select an answer

What information is contained in the survey figure prefix database?

(Select one)

The surface figures that will be used for elevations.
The layer that figures will be drawn on.
The figures that will be created as alignments.
The figures that will be created as pipe networks.

Select an answer

Please refer to the exhibit:

What is the most efficient way to add major and minor station labels at specified intervals along an alignment?

(Select one)

Use match properties to copy a label set from one alignment to another.
Place labels using station and offset in the Add Labels dialog.
Place labels between two points using the Add Labels dialog.
Place multiple labels and types along an alignment using a label set.

Select an answer

How are raw descriptions assigned a full description?

(Select one)

Survey Database
Properties Palette
Description Key Set
Point Group

Select an answer

After a surface analysis is performed, how is it displayed in a drawing?

(Select one)

Make the surface analysis type visible in the surface style.
Adjust the display of the surface analysis layer in the drawing.
Make the surface analysis type visible in the surface properties.
Open the panorama palette and enable the display of the analysis.

Select an answer

A drawing contains a long linear project with a polyline representing the alignment. What should be used to create multiple plan only sheets?

(Select one)

Create View Frames, Create Alignment from Object, Create Sheets
Create View Frames, Create Sheets, Create Alignment from Object
Create Alignment from Object, Create View Frames, Create Sheets
Create Alignment from Object, Create Sheets, Create View Frames

Select an answer

Which pressure pipe editing tool will automatically adjust pipe elevations based on a predetermined depth below a selected surface?

(Select one)

Design Check
Pipe Run Profile
Draw Parts in Profile View
Depth Check

Select an answer

A large linear project contains an alignment than spans multiple sheets. How should you annotate where the multiple sheets have been divided?

(Select one)

Use the Insert Match Lines command on the Home ribbon tab in the Alignment drop-down menu.
Select the alignment and use the Insert Match Lines command in the contextual ribbon.
Select Insert Match Lines in the Create View Frames wizard.
Use the Insert Match Lines command on the Home ribbon tab in the Create Design panel drop-down menu.

Select an answer

For a roadway project that extends across several sheets, how should the bearings and distances be annotated?

(Select one)

Place labels with an As Composed dragged state.
Place tag labels with a spiral table.
Place labels in a dragged state.
Place tag label with a segment table.

Select an answer

When a design profile between two existing roads creates too much cut or fill, which of these workflows should resolve the issue?

(Select one)

Run a cut fill analysis on the corridor surface to balance the cut and fill of the design profile.
Raise or lower all vertices of the design profile to more closely match the existing surface.
Insert additional points of intersection or vertical curves to more closely match the existing surface.
Add spirals to the vertical curves to more closely match the existing surface.

Select an answer

What is unique about feature lines created from a corridor?

(Select one)

They can remain dynamically linked to the original corridor.
They can't be added to a corridor surface.
They cannot be used as corridor targets.
They can remain dynamically linked to a surface.

Select an answer

Please refer to the exhibit:

An Existing Ground surface has been created. The contour labeled "Contour A" does not correctly represent the curb and gutter identified with the survey points shown. Which of these workflows should be performed to produce the contour labeled "Contour B" in the Existing Ground surface?

(Select one)

Smooth the surface.
Add points to the drawing.
Add breaklines to the surface.
Remove points from the surface.

Select an answer

How are elevations of a TIN surface calculated?

(Select one)

Figures and contours map geometrically banded elevation data.
Points and lines that are closely connected form grids of elevation data that define any point in the surface by the gridded interpolation of the cross and running slope of the faces of the surface.
Points and lines that are closely connected form triangulated areas that define any point in the surface by interpolating the elevations of the vertices of the triangles that the point lies in. ( ) Point clouds of data that are closely mapped are netted to allow linear interpolation of any point data contained in the surface.

Select an answer

A point group named HIDE is created. It includes all points, has point styles and point label styles set to None, and style overrides are enabled. What is the result of point visibility in the drawing if this point group is at the top of the point group list?

(Select one)

Only points that are in the Description Key Set will be visible in the drawing.
All points and labels will be visible in the drawing.
No points or labels will be visible in the drawing.
All points in the drawing will be visible except those that are in the Description Key Set.

Select an answer

Please refer to the exhibit:
The point labeled 1 is in a base drawing with UCS set to World. The point labeled 2 is how the point looks on a sheet with a different view rotation. What change should be made in the base drawing so that the COGO point labeled as 2 will match the correct rotation labeled as 1 in all sheet viewport rotations?

(Select one)

Modify the point style marker Orientation Reference to View and then save.
Modify the fixed marker rotation in the Description Key Set and then save.
Modify the point style marker rotation angle and then save.
Modify the point marker rotation in the Properties palette and then save.

Select an answer

A proposed utility line crosses from within a public right-of-way into a public utility easement. Which of these workflows will include a label at this location in the profile view?

(Select one)

Add a vertex to the alignment at the crossing and then show geometry grid lines onto the profile view.
Place a COGO point at the crossing and then project it onto a profile view.
Place an AutoCAD point at the crossing and then project it onto a profile view.
Add a polyline perpendicular to the utility alignment at the crossing and then project it onto the profile view.

Select an answer

After creating a temporary rough grading surface with feature lines, how can grading groups for the proposed surface be prevented from interacting with these temporary surface feature lines?

(Select one)

In the grading group properties disable the Feature Line Interaction setting.
Change the feature line style for the feature lines used in the temporary surface.
The proposed surface grading groups should be based on feature lines that are not in a site (Site ).
The feature lines for the temporary surface should be in a separate site from the proposed surface grading group.

Select an answer

What is the most efficient way to resolve variable width corridors with daylighting subassemblies that overlap without leaving any gaps in the daylight areas?

(Select one)

Manually modify the subassembly slopes.
Use the Clear Corridor Bowties tool.
Grip edit the daylight locations.
Create separate regions.

Select an answer

Please refer to the exhibit:
A proposed pipe network crosses three surfaces: EG (existing grade), SG (site grading) and RG (road grading). Some site grading (SG) content overlaps the road grading (RG) content. To confirm minimum depth requirements, which workflow will create the required final design surface for the proposed pipe network to reference?

(Select one)

Paste SG surface and then RG surface into the EG surface.
Create a new surface, paste EG surface, paste RG surface, paste SG surface.
Create a new surface, paste SG surface, paste RG surface, paste EG surface.
Paste EG surface and then RG surface into the SG surface.

Select an answer

To automatically size tree blocks based on diameter, which point parameter would be used?

(Select one)

apply to Z
fixed scale factor
use drawing scale
scale parameter

Select an answer

Please refer to the exhibit:

After adding a crossing pipe to a profile view, where should the display settings be modified so that the red pipe appears as shown in the exhibit?

(Select one)

Part List
Profile View Properties
Geometry Editor
Network Properties

Select an answer

Which type of surface analysis is typically used to show cut fill calculations?

(Select one)

elevations
volumes
directions
slopes

Select an answer

What objects can be created from a corridor?

(Select one)

profiles, alignments, grading group
feature lines, surfaces, point groups
alignments, feature lines, profiles
alignments, surfaces, pipe networks

Select an answer

Which of the following transparent commands should be used with the POLYLINE command to create a property boundary based on a recorded document?

(Select one)

deflection distance
bearing distance
station from plan
station offset

Select an answer

Please refer to the exhibit:

The alignment label set shown in area (A) is imported to the alignment shown in area B. What is the result?

(Select one)

One set each of major station labels, minor station labels, and geometry point labels.
One set of geometry point labels.
One set each of major station labels and minor station labels.
Two sets each of major and minor station labels and one set of geometry point labels.

Select an answer

What type of object is needed to create sample lines?

(Select one)

Feature line
Spline
Alignment
Polyline

Select an answer

A drawing contains an existing ground surface, a feature line representing the centerline of a drainage ditch, and a drainage ditch assembly that includes daylight subassemblies. Which of these steps in the order shown will result in a corridor that represents the proposed drainage ditch?

(Select one)

Use the Create Corridor From Objects command to apply the drainage ditch assembly along the feature line at specified intervals with the existing ground surface as a target.
Use the Create Profile From Objects command to create a profile from the feature line. Then create a corridor with the feature line as a baseline and using the profile with the drainage ditch assembly and existing ground surface as a target.
Use the Create Alignment From Objects command to create an alignment from the feature line. Then create a corridor using the alignment as a baseline with the drainage ditch assembly and assign the existing ground surface as a target.
Use the Corridor command to create a corridor using the feature line as a baseline with the drainage ditch assembly. Then assign the existing ground surface as a target.

Select an answer

Please refer to the exhibit:

What step or steps should be taken to combine the two feature lines as shown in area (A) to make a single feature line as shown in area (B)?

(Select one)

Use the Fillet command with radius 0.
Use the FilletFeatures command with a radius of 0.
Use the Trim command and then the Join command.
Use the TrimFeatures command and then the JoinFeatures command.

Select an answer

What type of point is created when using the Point Creation toolbar?

(Select one)

Survey point
AutoCAD point node
AutoCAD blocks
COGO point

Select an answer

Please refer to the exhibit:

A feature line for the proposed curb edge of asphalt (A) has been created. Feature lines for the rest of the curb (B, C, and D) need to be created. The new feature lines need to have appropriate elevations assigned based on the exhibit. Which feature line command should be used?

(Select one)

Create Feature Line
Create Feature Line from Stepped Offset
Create Feature Line from Objects
Create Feature Line from Alignment

Select an answer

To show contours within an interior courtyard surrounded by a building, what type of boundary should be used?

(Select one)

Show
Outer
Inner
Data clip

Select an answer

When creating multiple section views, what is required in the specified production template?

(Select one)

An initialized layout with a viewport and type set to Undefined and annotation scale set to match the current drawing.
A border, north arrow, and viewport extents outlined in model space.
A border and north arrow in model space.
An initialized layout with a viewport and type set to Section and annotation scale set to match the current drawing.

Select an answer

A single drawing contains multiple Civil 3D elements including alignments, surfaces, and pipe networks. To reduce the amount of time needed to open the drawing and to provide edit access to multiple team members, what should be done?

(Select one)

Create separate drawings and then attach externals references for each Civil 3D element.
Create separate drawing with datalinks to an external database of Civil 3D element definitions.
Create separate drawing and use view frames and a sheet set to access each Civil 3D element.
Create separate drawing with data shortcuts for each Civil 3D element needed in the other drawings.

Select an answer

A drawing contains back of curb feature lines with elevations based on a rough grading surface. Which of these workflows will create a corridor with curbs?

(Select one)

Use stepped offset to create feature lines for the curb then add each feature line to the corridor as a baseline.
Create alignments from the feature lines, add these alignments as baselines, add the feature lines as elevations, and then assign a curb assembly to each baseline.
Add the feature lines as baselines in the corridor and assign a curb assembly to each baseline.
Create sample lines and apply a curb assembly to each frequency along the baselines.

Select an answer

Please refer to the exhibit: A parcel segment curve table has been created. The curve tag numbers are not in the correct order which is shown as numbers in green circles. How should the curve tag numbers be corrected and maintain the dynamic link to the curve segment table for future design changes?

(Select one)

Explode the curve tags and table then edit the text to match the desired result.
Drag the tag number to the correct location with a manual leader.
Select a parcel and use the Renumber Tags command in the Parcel contextual ribbon.
Use the Edit Label Text command to edit the curve tag numbers.

Select an answer

After creating different grading objects for two portions of a feature line, what type of grading object should be created to connect the two grading objects?

(Select one)

Slope to surface
Conflict resolution
Transition
Infill

Select an answer

In addition to lines and curves, what other object types can be made into an alignment using the Create Alignments from Objects command?

(Select one)

feature lines
survey figures
polylines
splines

Select an answer

When creating an alignment using the Alignment Layout Tools, what are possible curve type options in the Curve and Spiral Settings?

(Select one)

parabolic, circular, and asymmetric
clothoid, bloss, and asymmetric
bi-quadratic, clothoid, and cubic parabola
bi-quadratic, clothoid, and circular

Select an answer

After creating the walls and berm of a pond, what will add the bottom of the pond to the Grading Group surface?

(Select one)

Create transition
Grade to surface
Create grading
Create infill

Select an answer

A large tract of land is going to be subdivided into lots and blocks. How should the first parcel be created?

(Select one)

Select a closed polyline that represents the original boundary of the tract and use the Create Parcel From Object command.
Select a closed survey figure that represents the original boundary of the tract and use the Create Parcel From Object command.
Use the Parcel Layout Tools Automatic Layout mode.
Use the Create Right of Way command.

Select an answer

Please refer to the exhibit:

Label (A) shows the elevation difference between crossing pipes in a profile view. This label remains linked to the profile view. What type of label is it?

(Select one)

AutoCAD linear dimension
Profile View Station Elevation label
Profile View Depth label
Profile View Projection label

Select an answer

When the Slope (Hold Start) value of a pipe is modified, which of these values will also change?

(Select one)

Slope and Start Invert Elevation
End Northing and End Easting
Start Northing and Start Easting
Slope and End Invert Elevation

Select an answer

Please refer to the exhibit:

What changes should be made to allow the profile view to fit inside the sheet viewport extent as outlined by the red polyline?

(Select one)

Profile View Properties > Elevations > Split profile views
Profile View Properties > Profiles > Split profile views
Profile View Style > Display > Split profile views
Profile View Style > Vertical Axes > Split profile views

Select an answer

The angular difference between grade in and grade out of a design profile is by more than the standard design specifications. If the proposed grades need to be maintained, how should the proposed profile be modified to resolve the design issue?

(Select one)

Add a vertical curve to the proposed profile.
Add a horizontal curve to the alignment.
Adjust the point of intersection of the profile.
Raise or lower the proposed profile.

Select an answer

If surface content is shown outside of an established surface boundary, what should be done to resolve the issue?

(Select one)

Move the outer boundary to the bottom of the surface definitions list.
Drag and drop the order of boundaries in Toolspace > Prospector.
Move the outer boundary to the top of the surface definitions list.
Drag and drop the order of surface edits in Toolspace > Prospector.

Select an answer

Before creating a data shortcut, what steps should be taken and in what order?

(Select one)

Set Working Folder, assign Project to Current Drawing, set Data Shortcuts Folder
Assign Project to Current Drawing, set Data Shortcuts Folder, set Working Folder
Set Working Folder, set Data Shortcuts Folder, assign Project to Current Drawing
Assign Project to Current Drawing, set Working Folder, set Data Shortcuts Folder

Select an answer

After placing structures at existing manhole locations, how should the rim elevation be set?

(Select one)

Adjust the surface elevation in the survey topo.
With Automatic Surface Adjustment set to False, set the Surface Adjustment value to the elevation from survey.
With Automatic Surface Adjustment set to False, set the Insertion Rim Elevation to the elevation from survey.
With Automatic Surface Adjustment set to True, set the Insertion Rim Elevations to the elevation from survey.

Select an answer

A proposed surface is being created. The design requires that the edge of an existing sidewalk remain as built. A feature line will be created from the polyline that represents the existing sidewalk. Which of these workflows will provide existing elevations that need to be matched in the proposed design?

(Select one)

After feature line creation, use the Stepped Offset command to assign elevations from the existing ground surface.
During feature line creation enable Weed Points in the Create Feature Lines dialog and choose the existing ground surface for reference.
During feature line creation enable Assign Elevations in the Create Feature Lines dialog and choose the existing ground surface for reference.
After feature line creation, use the Insert Elevation command to assign elevations from the existing ground surface.

Select an answer

A bend is what type of Civil 3D Pressure Pipe object?

(Select one)

Pressure pipe
Appurtenance
Fitting
Structure

Select an answer

49/49 questions left unanswered

Pre-test

Pre-assessment

What alignment is the width of a widening alignment based on?

What information is contained in the survey figure prefix database?

Please refer to the exhibit: What is the most efficient way to add major and minor station labels at specified intervals along an alignment?

How are raw descriptions assigned a full description?

After a surface analysis is performed, how is it displayed in a drawing?

A drawing contains a long linear project with a polyline representing the alignment. What should be used to create multiple plan only sheets?

Which pressure pipe editing tool will automatically adjust pipe elevations based on a predetermined depth below a selected surface?

A large linear project contains an alignment than spans multiple sheets. How should you annotate where the multiple sheets have been divided?

For a roadway project that extends across several sheets, how should the bearings and distances be annotated?

When a design profile between two existing roads creates too much cut or fill, which of these workflows should resolve the issue?

What is unique about feature lines created from a corridor?

How are elevations of a TIN surface calculated?

A point group named HIDE is created. It includes all points, has point styles and point label styles set to None, and style overrides are enabled. What is the result of point visibility in the drawing if this point group is at the top of the point group list?

A proposed utility line crosses from within a public right-of-way into a public utility easement. Which of these workflows will include a label at this location in the profile view?

After creating a temporary rough grading surface with feature lines, how can grading groups for the proposed surface be prevented from interacting with these temporary surface feature lines?

What is the most efficient way to resolve variable width corridors with daylighting subassemblies that overlap without leaving any gaps in the daylight areas?

To automatically size tree blocks based on diameter, which point parameter would be used?

Please refer to the exhibit: After adding a crossing pipe to a profile view, where should the display settings be modified so that the red pipe appears as shown in the exhibit?

Which type of surface analysis is typically used to show cut fill calculations?

What objects can be created from a corridor?

Which of the following transparent commands should be used with the POLYLINE command to create a property boundary based on a recorded document?

Please refer to the exhibit: The alignment label set shown in area (A) is imported to the alignment shown in area B. What is the result?

What type of object is needed to create sample lines?

A drawing contains an existing ground surface, a feature line representing the centerline of a drainage ditch, and a drainage ditch assembly that includes daylight subassemblies. Which of these steps in the order shown will result in a corridor that represents the proposed drainage ditch?

Please refer to the exhibit: What step or steps should be taken to combine the two feature lines as shown in area (A) to make a single feature line as shown in area (B)?

What type of point is created when using the Point Creation toolbar?

To show contours within an interior courtyard surrounded by a building, what type of boundary should be used?

When creating multiple section views, what is required in the specified production template?

A single drawing contains multiple Civil 3D elements including alignments, surfaces, and pipe networks. To reduce the amount of time needed to open the drawing and to provide edit access to multiple team members, what should be done?

A drawing contains back of curb feature lines with elevations based on a rough grading surface. Which of these workflows will create a corridor with curbs?

After creating different grading objects for two portions of a feature line, what type of grading object should be created to connect the two grading objects?

In addition to lines and curves, what other object types can be made into an alignment using the Create Alignments from Objects command?

When creating an alignment using the Alignment Layout Tools, what are possible curve type options in the Curve and Spiral Settings?

After creating the walls and berm of a pond, what will add the bottom of the pond to the Grading Group surface?

A large tract of land is going to be subdivided into lots and blocks. How should the first parcel be created?

Please refer to the exhibit: Label (A) shows the elevation difference between crossing pipes in a profile view. This label remains linked to the profile view. What type of label is it?

When the Slope (Hold Start) value of a pipe is modified, which of these values will also change?

Please refer to the exhibit: What changes should be made to allow the profile view to fit inside the sheet viewport extent as outlined by the red polyline?

The angular difference between grade in and grade out of a design profile is by more than the standard design specifications. If the proposed grades need to be maintained, how should the proposed profile be modified to resolve the design issue?

If surface content is shown outside of an established surface boundary, what should be done to resolve the issue?

Before creating a data shortcut, what steps should be taken and in what order?

After placing structures at existing manhole locations, how should the rim elevation be set?

A bend is what type of Civil 3D Pressure Pipe object?

Please refer to the exhibit:

What is the most efficient way to add major and minor station labels at specified intervals along an alignment?

Please refer to the exhibit:

After adding a crossing pipe to a profile view, where should the display settings be modified so that the red pipe appears as shown in the exhibit?

Please refer to the exhibit:

The alignment label set shown in area (A) is imported to the alignment shown in area B. What is the result?

Please refer to the exhibit:

What step or steps should be taken to combine the two feature lines as shown in area (A) to make a single feature line as shown in area (B)?

Please refer to the exhibit:

Label (A) shows the elevation difference between crossing pipes in a profile view. This label remains linked to the profile view. What type of label is it?

Please refer to the exhibit:

What changes should be made to allow the profile view to fit inside the sheet viewport extent as outlined by the red polyline?