Which of the following is true of the solid generated by the In-Process Stock functionality?

(Select one)

It can be modified using the Solid toolset
It can be modified using the Mesh toolset
It can be modified using the Form toolset
It is simply there for visualization and cannot be used with any CAD tools

Select an answer

Which of the following cycles for a Drill operation will cause the tool to periodically retract the tool from the hole?

(Select one)

Tapping
Chip breaking
Counterboring
Boring

Select an answer

When is the No Dragging option in the Passes tab typically used?

(Select one)

When the tool will encounter a vertical face during a pass
When the tool needs to retract periodically during a pass
When the operation should ignore grooves in the part
When the operation is for roughing and stock needs to be left over

Select an answer

Where in a Drill operation can the user control the depth of the drill’s tip?

(Select one)

Heights > Retract Height
Heights > Drill Tip Through Bottom
Cycle > Cycle Type
Geometry > Hole Mode

Select an answer

Where in the Manufacture workspace can the Section Analysis tool be found?

(Select one)

Workspace dropdown
Display Settings bar
Marking menu
Inspect dropdown

Select an answer

How can operation order be modified to automatically minimize tool changes?

(Select one)

Configure this option in the NC Program window
Right-click the setup in the Browser and select Create Manual Inspection
Enable the Continue Rest Machining option in the Stock tab of the Setup dialog
There is no option to automatically change operation order based on tool changes

Select an answer

Which of the following controls the exit path of a Turning Thread toolpath pass?

(Select one)

Fade Thread End
Infeed Mode
Thread Depth
Retract Offset

Select an answer

What color on a simulated view of the part will show that a toolpath is in-tolerance?

(Select one)

Red
Purple
Blue
Green

Select an answer

What setting controls the distance that the tool starts and ends at in the X-direction for all toolpaths?

(Select one)

Approach & Retract
Confinement
Outer Radius
Clearance

Select an answer

For a part with several cosmetic and modeled thread geometry, how can all threads be converted to cosmetic efficiently?

(Select one)

Modify the Threads option under Document Settings in the Browser
Use Remove Features in the Simplify toolset of the Simulation workspace
Find each Thread operation in the timeline and ensure the Modeled option is unchecked
Delete each modeled thread face and create a new Thread with Modeled unchecked

Select an answer

For a tool with number 3 and diameter offset 3 in the Setup Sheet, what would the posted NC code designate the tool as?

(Select one)

T33
T3D3
T303
T3

Select an answer

For a Turning Profile Finishing operation, which of the follow tabs contains the option to prevent the tool from machining grooves on the part?

(Select one)

Linking
Geometry
Passes
Radii

Select an answer

If the Feed scale (%) is reduced below 100%, what affect does it have on the Total feed time value?

(Select one)

The Feed scale (%) is a driven value and cannot be changed
It decreases Total feed time
It has no effect on Total feed time
It increases Total feed time

Select an answer

How can the machining time for individual operations in a setup be determined?

(Select one)

Use Info tab of Simulate tool with the operation of interest selected
Use the Measure tool with the operation of interest selected
Use Display tab of Simulate with the operation of interest selected
Use Statistics tab of Simulate tool with the operation of interest selected

Select an answer

How can the distance that the tool starts and ends at along the length of the part be controlled?

(Select one)

Adjust the Tolerance value in the Passes tab
Adjust the Safe Z value in the parent Setup of the operation
Enable Stock to Leave and enter the appropriate distances
Adjust the Clearance and Retract settings in the Radii tab

Select an answer

When an operation is selected in the Browser, what is the visualization of the model and stock shown in the window referred to as?

(Select one)

In-process Stock
Simulated Stock
Rest Machined Stock
Rendered Stock

Select an answer

Which Tool visualization option in the Simulate dialog will only show the insert of the tool?

(Select one)

Flute
Shaft
There is no such visualization option
Holder

Select an answer

Which of the following can be done in the Radii tab to ensure that the tool does not cut too deep?

(Select one)

Select the outermost face of the part to stay within under the Outer Radius setting
Increase the offset under the Clearance setting
Decrease the offset under the Retract setting
Select the deepest face to stay outside of under the Inner Radius setting

Select an answer

Which of the following extensions is associated with an importable file that contains all relevant tool information?

(Select one)

.tools
.mach
.f3d
.mfg

Select an answer

Which of the following settings in the Setup dialog of the Manufacture workspace can be used to control the retract position of the tool before or after a toolpath?

(Select one)

Spindle
Z Axis (Rotary Axis)
Chuck reference
Safe Z

Select an answer

Which keyboard shortcut while in the Manufacture workspace will toggle In-Process Stock visibility?

(Select one)

F1
CTRL
F8
SPACEBAR

Select an answer

Which setting in the Turning Part toolpath can be used to introduce a fillet or chamfer at the separation point?

(Select one)

Transfer Stock
Make Sharp Corners
Back Mode
Edge Break

Select an answer

What color is applied outside the Simulate tool to a chamfered edge for a Turning Chamfer toolpath on an un-modeled chamfer?

(Select one)

Blue
Yellow
Orange
Green

Select an answer

Which of the following statements best describes a use of the Show Tool on Cursor visualization option?

(Select one)

It can be used to compute the exact interference distance between the tool and the stock
It can be used to measure the inner and outer radii of different features of the part
It can be used to detect the presence of collisions throughout a programmed toolpath
It can be used to inspect if a specific tool is suitable for a specific feature on the model

Select an answer

Which of the following is true of the Max spindle speed parameter in the Post properties of the NC Program window?

(Select one)

This value will be used to remove all toolpaths that exceed it
This value will create a global cap for toolpath speeds that may try to exceed this
This value is simply defined by the machine and has no effect on the toolpaths that are processed
This value will scale all operations to the max spindle speeds

Select an answer

Which of the following pieces of information is shown in the Operations section of a detailed Setup Sheet?

(Select one)

Machine vendor for that operation
Tool material for tool used in that operation
Total stock volume
Estimated cycle time for that operation

Select an answer

Which of the following settings in a Turning Thread toolpath can be used to indicate if the threads are within a hole or on an outside face?

(Select one)

Threading Hand
Do Multiple Threads
Turning Mode
Confinement

Select an answer

Which of the following parameters is unavailable in the posted code of an NC program?

(Select one)

Spindle speed
Machine specification
Tool number
Tool wear

Select an answer

How can the parameters of a tool from the sample Fusion 360 Library be modified?

(Select one)

Right-click the tool in the samples library and select Edit
Export the tool as a CAD model and modify the tools in the Design workspace
Copy and paste it into a local or cloud library to edit
No action can be taken to modify a tool from the samples library

Select an answer

Which stock Colorization option the Simulate dialog should be used to show gouged material?

(Select one)

Operation
Tool
Material
Comparison

Select an answer

Start your final test

CAM Strategies for Turning Final Test

Which of the following is true of the solid generated by the In-Process Stock functionality?

Which of the following cycles for a Drill operation will cause the tool to periodically retract the tool from the hole?

When is the No Dragging option in the Passes tab typically used?

Where in a Drill operation can the user control the depth of the drill’s tip?

Where in the Manufacture workspace can the Section Analysis tool be found?

How can operation order be modified to automatically minimize tool changes?

Which of the following controls the exit path of a Turning Thread toolpath pass?

What color on a simulated view of the part will show that a toolpath is in-tolerance?

What setting controls the distance that the tool starts and ends at in the X-direction for all toolpaths?

For a part with several cosmetic and modeled thread geometry, how can all threads be converted to cosmetic efficiently?

For a tool with number 3 and diameter offset 3 in the Setup Sheet, what would the posted NC code designate the tool as?

For a Turning Profile Finishing operation, which of the follow tabs contains the option to prevent the tool from machining grooves on the part?

If the Feed scale (%) is reduced below 100%, what affect does it have on the Total feed time value?

How can the machining time for individual operations in a setup be determined?

How can the distance that the tool starts and ends at along the length of the part be controlled?

When an operation is selected in the Browser, what is the visualization of the model and stock shown in the window referred to as?

Which Tool visualization option in the Simulate dialog will only show the insert of the tool?

Which of the following can be done in the Radii tab to ensure that the tool does not cut too deep?

Which of the following extensions is associated with an importable file that contains all relevant tool information?

Which of the following settings in the Setup dialog of the Manufacture workspace can be used to control the retract position of the tool before or after a toolpath?

Which keyboard shortcut while in the Manufacture workspace will toggle In-Process Stock visibility?

Which setting in the Turning Part toolpath can be used to introduce a fillet or chamfer at the separation point?

What color is applied outside the Simulate tool to a chamfered edge for a Turning Chamfer toolpath on an un-modeled chamfer?

Which of the following statements best describes a use of the Show Tool on Cursor visualization option?

Which of the following is true of the Max spindle speed parameter in the Post properties of the NC Program window?

Which of the following pieces of information is shown in the Operations section of a detailed Setup Sheet?

Which of the following settings in a Turning Thread toolpath can be used to indicate if the threads are within a hole or on an outside face?

Which of the following parameters is unavailable in the posted code of an NC program?

How can the parameters of a tool from the sample Fusion 360 Library be modified?

Which stock Colorization option the Simulate dialog should be used to show gouged material?