• Revit

Create a roof in Revit

Place a roof in Revit.


Tutorial resources

These downloadable resources will be used to complete this tutorial:


00:04

When you create a roof in Revit, you need to sketch the boundaries of the roof.

00:09

There are several tools you can use when creating roofs.

00:13

The default is the Roof by Footprint tool,

00:18

which allows you to place a roof by creating a roof profile and then extruding the profile.

00:24

To complete this exercise, open the CreatingRoofs [2024].rvt exercise file.

00:32

To begin, from the Project Browser, open the Level 4 floor plan view.

00:39

On the Architecture ribbon, in the Build panel, expand the Roof drop-down and select Roof by Footprint.

00:49

When you do, you enter into sketch mode.

00:53

Notice on the Draw panel, Boundary Line is selected by default.

00:58

In the Draw gallery, Pick Walls is the default, but you can use any of the other Draw tools to sketch a roof.

01:08

For this example, select Pick Walls.

01:12

In the Options bar, you can specify if you want the roof to slope, enter an Overhang value,

01:19

or specify if you want the roof to Extend to wall core, rather than the finished face.

01:26

In the Options bar, disable Defines slope, and then select Extend to wall core.

01:36

Expand the Type Selector and choose the type of roof you want to create.

01:43

You can create a Basic Roof or Sloped Glazing.

01:47

For this example, select one of the basic roofs.

01:52

Next, hover your cursor over an existing wall.

01:57

When it highlights, press TAB to highlight the entire chain of walls.

02:04

Then, click to select them.

02:08

You can use the flip control to change whether the boundary lines are on the exterior or interior face of the walls.

02:18

Make sure the sketch lines appear on the interior face of the walls, and then click Finish Edit Mode.

02:28

Note that if the boundary lines are not in a closed loop, or if any line segments overlap, the tool will yield a warning error.

02:37

Revit displays a confirmation dialog.

02:41

Because you selected Extend to wall core and the roof currently overlaps the walls,

02:47

you must confirm that you want to cut the overlapping volume from the walls.

02:52

Click Yes.

02:54

Switch to a 3D view to see the roof that you just created.

Video transcript

00:04

When you create a roof in Revit, you need to sketch the boundaries of the roof.

00:09

There are several tools you can use when creating roofs.

00:13

The default is the Roof by Footprint tool,

00:18

which allows you to place a roof by creating a roof profile and then extruding the profile.

00:24

To complete this exercise, open the CreatingRoofs [2024].rvt exercise file.

00:32

To begin, from the Project Browser, open the Level 4 floor plan view.

00:39

On the Architecture ribbon, in the Build panel, expand the Roof drop-down and select Roof by Footprint.

00:49

When you do, you enter into sketch mode.

00:53

Notice on the Draw panel, Boundary Line is selected by default.

00:58

In the Draw gallery, Pick Walls is the default, but you can use any of the other Draw tools to sketch a roof.

01:08

For this example, select Pick Walls.

01:12

In the Options bar, you can specify if you want the roof to slope, enter an Overhang value,

01:19

or specify if you want the roof to Extend to wall core, rather than the finished face.

01:26

In the Options bar, disable Defines slope, and then select Extend to wall core.

01:36

Expand the Type Selector and choose the type of roof you want to create.

01:43

You can create a Basic Roof or Sloped Glazing.

01:47

For this example, select one of the basic roofs.

01:52

Next, hover your cursor over an existing wall.

01:57

When it highlights, press TAB to highlight the entire chain of walls.

02:04

Then, click to select them.

02:08

You can use the flip control to change whether the boundary lines are on the exterior or interior face of the walls.

02:18

Make sure the sketch lines appear on the interior face of the walls, and then click Finish Edit Mode.

02:28

Note that if the boundary lines are not in a closed loop, or if any line segments overlap, the tool will yield a warning error.

02:37

Revit displays a confirmation dialog.

02:41

Because you selected Extend to wall core and the roof currently overlaps the walls,

02:47

you must confirm that you want to cut the overlapping volume from the walls.

02:52

Click Yes.

02:54

Switch to a 3D view to see the roof that you just created.

Was this information helpful?