• InfraWorks

Build a walkway network and add people areas in Mobility Simulation

Build a walkway network and add people areas for a queuing system simulation.


00:04

One way to use InfraWorks Mobility Simulation is to create an animated queuing system, as you might find at airports and attractions.

00:12

The first step in this process is building the network of walkways and people areas where pedestrian movement will be simulated.

00:20

With a new model open in Mobility Simulation, ensure you are in orthographic mode by typing the letter O.

00:28

Then, click the top of the ViewCube to orient the model to plan view.

00:33

From the Tabs panel, select Layer.

00:36

Each Layer can be switched on or off in any Aspect by pressing the toggle button.

00:41

In this case, enable the first column of Walk Centrelines, Walk Connections, Handle – End, and Handle – Other.

00:49

Using your mouse wheel, zoom in closer to your simulation.

00:53

Right-click the simulation and expand Walkway, then select New Walkway at Cursor.

00:60

In the New Walkway dialog, change the Length to 15 and the Width to 1.5.

01:06

Click OK and the new walkway appears.

01:10

Zoom in for a closer look..

01:12

It is important to set the parameters properly for this first walkway,

01:16

because you will copy it to create the additional walkways.

01:20

Select the walkway, then right-click and select Adjust.

01:23

In the Adjust dialog, enable the boxes in the Walled L and Walled R columns.

01:30

Then, enter a Wall Height of 0.01.

01:34

Click Apply.

01:36

To create another walkway, select the first walkway, then right-click and select Edit > Copy.

01:43

Now, right-click and select Edit > Paste.

01:47

The new walkway appears on top of the initial walkway.

01:51

Click and drag the new walkway to the right of the first one.

01:55

Right-click and select Edit > Paste twice more, dragging each walkway to a new location, so that you now have four walkways.

02:05

Continue to paste additional walkways until you have the number needed to complete your layout.

02:11

You can click the end handle of any walkway and drag to rotate or lengthen the walkway.

02:17

In this example a total of 14 walkways are created, resized, and rotated to create the basic layout of a queue system.

02:26

Next, the walkways need to be connected.

02:30

Zoom in to 2 walkways that you want to connect, and use the middle mouse button to click the ends to be connected.

02:36

Then, right-click and select Walkway > New Connection.

02:41

A connection is automatically made between the two walkways.

02:46

To connect three walkways, use the same method to connect 2 of the walkways, and press ESC to deselect them.

02:52

Now, click the end of the third walkway, and then click one of the end handles of the 2 you just connected.

02:59

Notice that this selects the full connection.

03:03

Right-click, and select Walkway > New Connection.

03:06

The center lines of the three walkways are now connected.

03:11

Follow this same process to finish connecting walkways in your network.

03:15

Mobility Simulation may display odd graphics, but these can be ignored as long as your center lines are connecting correctly.

03:22

Once your network is completed, you can add people areas.

03:27

Center the handle of the topmost walkway just over the top of the cursor.

03:33

Note that this exact placement is critical to ensure that the walkway is fully embedded in the area.

03:40

Right-click and select Area > New Area At Cursor.

03:44

The area is added and the walkway now appears highlighted, indicating that it is properly embedded.

03:50

Follow this same process to add people areas at all open ends of the queue system.

03:56

Once you have created a queuing system of connected walkways and people areas,

04:00

you are ready to add people parameters to simulate pedestrian movement.

Video transcript

00:04

One way to use InfraWorks Mobility Simulation is to create an animated queuing system, as you might find at airports and attractions.

00:12

The first step in this process is building the network of walkways and people areas where pedestrian movement will be simulated.

00:20

With a new model open in Mobility Simulation, ensure you are in orthographic mode by typing the letter O.

00:28

Then, click the top of the ViewCube to orient the model to plan view.

00:33

From the Tabs panel, select Layer.

00:36

Each Layer can be switched on or off in any Aspect by pressing the toggle button.

00:41

In this case, enable the first column of Walk Centrelines, Walk Connections, Handle – End, and Handle – Other.

00:49

Using your mouse wheel, zoom in closer to your simulation.

00:53

Right-click the simulation and expand Walkway, then select New Walkway at Cursor.

00:60

In the New Walkway dialog, change the Length to 15 and the Width to 1.5.

01:06

Click OK and the new walkway appears.

01:10

Zoom in for a closer look..

01:12

It is important to set the parameters properly for this first walkway,

01:16

because you will copy it to create the additional walkways.

01:20

Select the walkway, then right-click and select Adjust.

01:23

In the Adjust dialog, enable the boxes in the Walled L and Walled R columns.

01:30

Then, enter a Wall Height of 0.01.

01:34

Click Apply.

01:36

To create another walkway, select the first walkway, then right-click and select Edit > Copy.

01:43

Now, right-click and select Edit > Paste.

01:47

The new walkway appears on top of the initial walkway.

01:51

Click and drag the new walkway to the right of the first one.

01:55

Right-click and select Edit > Paste twice more, dragging each walkway to a new location, so that you now have four walkways.

02:05

Continue to paste additional walkways until you have the number needed to complete your layout.

02:11

You can click the end handle of any walkway and drag to rotate or lengthen the walkway.

02:17

In this example a total of 14 walkways are created, resized, and rotated to create the basic layout of a queue system.

02:26

Next, the walkways need to be connected.

02:30

Zoom in to 2 walkways that you want to connect, and use the middle mouse button to click the ends to be connected.

02:36

Then, right-click and select Walkway > New Connection.

02:41

A connection is automatically made between the two walkways.

02:46

To connect three walkways, use the same method to connect 2 of the walkways, and press ESC to deselect them.

02:52

Now, click the end of the third walkway, and then click one of the end handles of the 2 you just connected.

02:59

Notice that this selects the full connection.

03:03

Right-click, and select Walkway > New Connection.

03:06

The center lines of the three walkways are now connected.

03:11

Follow this same process to finish connecting walkways in your network.

03:15

Mobility Simulation may display odd graphics, but these can be ignored as long as your center lines are connecting correctly.

03:22

Once your network is completed, you can add people areas.

03:27

Center the handle of the topmost walkway just over the top of the cursor.

03:33

Note that this exact placement is critical to ensure that the walkway is fully embedded in the area.

03:40

Right-click and select Area > New Area At Cursor.

03:44

The area is added and the walkway now appears highlighted, indicating that it is properly embedded.

03:50

Follow this same process to add people areas at all open ends of the queue system.

03:56

Once you have created a queuing system of connected walkways and people areas,

04:00

you are ready to add people parameters to simulate pedestrian movement.

Was this information helpful?